kcb483.3齒輪泵流量29m3/h(483.3l/min),壓力0.36mpa,吸入真空高度3米,效率42%,口徑70,配用電機7.5kw-4或者11kw-4.

      kcb483.3齒輪泵産品圖片

      輸送柴油油使用銅輪防止在輸送過程中,金屬摩擦産生火花,發生燃燒.所以在輸送汽柴油工況,我公司推薦客戶使用銅輪齒輪泵.

        kcb齒輪油泵在輸油系統中可用作傳輸、增壓泵；kcb gear oil pump in the oil system can be used as a transport, booster pump;

   在燃油系統中可用作輸送、加壓、噴射的燃油泵；in the fuel system can be used as a transport, pressure, jet fuel pump;

   在一切工業領域中，均可作潤滑油泵用。in all industrial areas, can be used as lubricating oil pump.

   kcb齒輪泵主要有齒輪、軸、泵體、安全閥、軸端密封所組成。齒輪經熱處理有較高的(de)硬度和強度，與軸一同安裝在可更換的(de)軸套内運轉。泵内全部零件的(de)潤滑均在泵工作時利用輸出介質而自動達到。kcb gear pump are mainly gear, shaft, pump body, valve, shaft end seal. gear after heat treatment with high hardness and strength, and shaft installed in the replaceable shaft sleeve. in all parts of the lubrication pump are pump work automatically to achieve using the output media.

   泵内有設計合理的洩油和回油槽，是齒輪在工作中承受的扭矩力最小，因此軸承負荷小，磨損小，泵效率高。pump is the drainage and back into the groove of reasonable design, is a gear in the work under the minimum torque force, so the bearing load is small, wear small, pump with high efficiency.

   泵設有安全閥作為超載保護，安全閥的全回流壓力為泵額定排除壓力的1.5倍，也可在允許排出壓力範圍内根據實際需要另外調整。但注意本安全閥不能作減壓閥的長期工作，需要時可在管路上另行安裝。從主軸外伸端向泵看，為順時針旋轉。pump is equipped with safety valve as overload protection, the total reflux pressure relief valve is rated pump out pressure of 1.5 times, also can allow discharge pressure range according to actual needs and adjust. but note that this cannot be a long-term work pressure reducing valve, relief valve can be installed in the piping shall be separately when necessary. to pump from the main shaft overhang end to see, for clockwise.

   流量：1.1m3/h-600m3/h壓力：0.28mpa--2.5mpa  traffic: 1.1 m3 / h - 600 m3 / h pressure: 0.28 mpa, 2.5 mpa 

   主要用于油田、油庫、港口、碼頭、船舶等大流量輸油，卸油！mainly used in oil fields, oil depot, ports, docks, ship big flow like oil, oil unloading!

   應用範圍:kcb/2cy型齒輪輸油泵适用于輸送粘度在300c.s.t以下的各種油類，如原油、柴油、潤滑油、動植物油等。配用銅齒輪可輸送低閃點液體，如汽油、苯等。介質溫度不超過70℃，耐高溫油泵的使用溫度不超過300℃。本泵身帶有安全閥，超載時起安全作用。軸封有骨架油封、機械密封、填料密封三種型式，訂貨注明。kcb齒輪潤滑泵主要用于各種機械設備中的(de)潤滑系統中輸送潤滑油，适用于輸送粘度在10oe（75c.s.t）以下，溫度在300℃以下的(de)具有潤滑性的(de)油料，不鏽鋼齒輪泵可輸送食用油料、飲料等。軸封有骨架油封、機械密封、填料密封三種型式.scope of application: kcb type / 2 cy gear oil pump is suitable for conveying viscosity at 300 c. s.t under various oil, such as crude oil, diesel oil, lubricating oil, animal and plant oil. with copper gear can handle liquid low flash point, such as gasoline, benzene, etc. medium temperature does not exceed 70 ℃, the use of high temperature resistant oil pump temperature does not exceed 300 ℃. when the pump body with a safety valve, overloading security role. shaft seal skeleton oil seal, mechanical seal, packing three type, indicate the order. kcb gear lubrication pump is mainly used for all kinds of mechanical equipment of conveying lubricating oil in the lubricating system, suitable for conveying viscosity in 10 oe (below 75 c. s.t), the temperature is below 300 ℃ with lubrication oil, stainless steel pump can transport edible oil, beverage and so on. shaft seal skeleton oil seal, mechanical seal, packing three types.

   kcb齒輪泵安裝說明:1、安裝泵的(de)地點應足夠寬敞，以方便檢修工作。2、泵安裝的(de)好壞，對泵的平穩運行和使用壽命有很重要的影響，所以安裝校正工作必須仔細地進行，不得草率行事。3、泵吸入管的安裝高度、長度和管徑應滿足計算值，力求簡短，減少不必要的(de)損失（如彎頭等）；并保證泵在工作時，不超過其允許汽蝕餘量。4、吸入和排出管路應該有支架。泵不允許承受管路的(de)負荷。kcb gear pump installation instructions: 1, the location of the installation of pump should be spacious enough, to facilitate maintenance and repair work. the stand or fall of 2, pump installation, for the smooth running of the pump and service life have very important influence, so the installation calibration work must be carried out carefully and must not be too hasty. 3, installation height of pump suction pipe, the length and diameter should satisfy the calculated value, to short, reduce unnecessary losses, such as elbow, etc.); and ensure the pump at work, no more than the allowed npsh. 4, suction and discharge line should be a support. pump are not allowed to bear load of pipeline.